Reverse Torque Loading Conditions Backstop Clutch
Basic Info
Model No.: NJD
Product Description
Model NO.: NJD Highest Speed of Inner Race: 50r/Min-150r/Min MOQ: 1set Package: Wooden Case, Iron Case, Iron Cage, Frame Specification: ISO9001: 2008 HS Code: 8483409000 Rated Holdback Moment Te: 11000n.M-1750000n.M Standards: ASTM,DIN,Sha,Cema.etc Terms of Shipment: by Sea Trademark: OUNA Origin: Toncheng, China Reverse Torque Loading Conditions Backstop Clutch
1. Structural features and operating principle
NJD(DSN) low-speed backstop(hereinafter referred to holdback) is a new type holdback device specially used for Belt Conveyor with big inclination and large conveying capacity.
This type of holdback is located using a bearing in which several shaped wedges are arranged in the raceway formed by inner race and outer race in a certain pattern so that it operates stably, the outer race is connected with two end covers, while the end covers are connected with the antirotation arm into an integral part through pins and the antirotation arm is limited by the fixed antirotation seat. When the motor operates normally, the holdback makes the wedges deflect by a certain angle through mechanics principle using the special geometry of the wedges so as to be in light contact with inner and outer race, thus reducing the coefficient of friction and improving the service life of the holdback. When the main motor needs to be shut down, the inner race of holdback reverses under the action of gravity of elevated material to drive the wedges to deflect and bring the inner race and outer race of the holdback to be wedged into an integral part so as to effectively prevent the motor from reversing. Therefore, this type of holdback is the most ideal non-reversing protector for conveying equipment such as large belt conveyor, Bucket Elevator etc.
2. Service environment
The ambient temperature for holdback operation is -20~50ºC, when the holdback is running, it will generate certain heat, so the ambient environment should be well ventilated, the temperature of the holdback running at allowable highest speed can reach 80ºC, in this case it is required to check the effect on the motor equipment and take appropriate temperature reduction measures, if necessary. When the ambient service temperature exceeds 38ºC or when it operates in open air, effective protective measures should be taken (for example, use ventilating equipment or cooling equipment etc.). Around the holdback it is not allowed to place corrosive chemicals for fear of damaging the holdback seal.
3,Main technical parameters of low-speed backstop
Notes: (1) It is recommended to adopt F7/h6 for the fit between the holdback hole and shaft (see Table 16) (if the user selects other fit, he shoud indicate this in the contract);
(2) The holdback hole and shaft are mainly connected with flat key, and the dimensions of key and keyway should satisfy the provisions of GB/T1095-1979. The keyway for the holdback hole is fabricated according to the tolerance D10 in GB/T1095-1979 (see Table 16).
(3) The length of shaft extension of the holdback should be equal to the length of inner race of the holdback as far as possible, its min. length should not be less than 5/6 length of inner race so as to ensure the strength of shaft extension and key.
Contact us if you need more details on Backstop. We are ready to answer your questions on packaging, logistics, certification or any other aspects about Bearing、Clutch. If these products fail to match your need, please contact us and we would like to provide relevant information.
1. Structural features and operating principle
NJD(DSN) low-speed backstop(hereinafter referred to holdback) is a new type holdback device specially used for Belt Conveyor with big inclination and large conveying capacity.
This type of holdback is located using a bearing in which several shaped wedges are arranged in the raceway formed by inner race and outer race in a certain pattern so that it operates stably, the outer race is connected with two end covers, while the end covers are connected with the antirotation arm into an integral part through pins and the antirotation arm is limited by the fixed antirotation seat. When the motor operates normally, the holdback makes the wedges deflect by a certain angle through mechanics principle using the special geometry of the wedges so as to be in light contact with inner and outer race, thus reducing the coefficient of friction and improving the service life of the holdback. When the main motor needs to be shut down, the inner race of holdback reverses under the action of gravity of elevated material to drive the wedges to deflect and bring the inner race and outer race of the holdback to be wedged into an integral part so as to effectively prevent the motor from reversing. Therefore, this type of holdback is the most ideal non-reversing protector for conveying equipment such as large belt conveyor, Bucket Elevator etc.
2. Service environment
The ambient temperature for holdback operation is -20~50ºC, when the holdback is running, it will generate certain heat, so the ambient environment should be well ventilated, the temperature of the holdback running at allowable highest speed can reach 80ºC, in this case it is required to check the effect on the motor equipment and take appropriate temperature reduction measures, if necessary. When the ambient service temperature exceeds 38ºC or when it operates in open air, effective protective measures should be taken (for example, use ventilating equipment or cooling equipment etc.). Around the holdback it is not allowed to place corrosive chemicals for fear of damaging the holdback seal.
3,Main technical parameters of low-speed backstop
Specification | Rated holdback moment (N.m) | Φ Max. hole diameter Φ (mm) | Highest speed of inner race (r/min) | Idle resistance moment (N.m) | Main installation dimensions | Max. mass (kg) | ||||||||
B | C | D | L | H | E | F | h | ΦA | ||||||
NJD(DSN)11 | 11000 | 110 | 150 | 15 | 100 | 60 | 270 | 110 | 425 | / | / | / | / | 77 |
NJD(DSN)16 | 16000 | 130 | 150 | 20 | 126 | 74 | 320 | 130 | 506 | / | / | / | / | 145 |
NJD(DSN)25 | 25000 | 160 | 150 | 32 | 140 | 80 | 360 | 140 | 612 | / | / | / | / | 198 |
NJD(DSN)40 | 40000 | 200 | 150 | 40 | 160 | 88 | 430 | 160 | 623 | / | / | / | / | 230 |
NJD(DSN)50 | 50000 | 220 | 100 | 70 | 200 | 100 | 500 | 230 | 820 | 110 | 50 | 70 | 35 | 385 |
NJD(DSN)100 | 100000 | 250 | 100 | 95 | 250 | 116 | 600 | 290 | 1000 | 120 | 55 | 70 | 40 | 696 |
NJD(DSN)130 | 130000 | 270 | 90 | 90 | 280 | 122 | 650 | 290 | 1100 | 120 | 60 | 80 | 40 | 812 |
NJD(DSN)200 | 200000 | 300 | 90 | 100 | 320 | 130 | 780 | 290 | 1300 | 135 | 60 | 80 | 45 | 1130 |
NJD(DSN)280 | 280000 | 320 | 90 | 130 | 360 | 140 | 850 | 320 | 1500 | 150 | 70 | 100 | 50 | 1480 |
NJD(DSN)330 | 330000 | 350 | 80 | 145 | 400 | 142 | 930 | 360 | 1600 | 160 | 70 | 100 | 55 | 1997 |
NJD(DSN)530 | 530000 | 420 | 80 | 200 | 450 | 146 | 1030 | 450 | 1800 | 180 | 80 | 120 | 60 | 3090 |
NJD(DSN)710 | 710000 | 450 | 80 | 225 | 500 | 160 | 1090 | 480 | 2000 | 210 | 100 | 120 | 70 | 3580 |
NJD(DSN)1000 | 1000000 | 510 | 70 | 260 | 560 | 170 | 1200 | 500 | 2200 | 230 | 110 | 150 | 80 | 4420 |
NJD(DSN)1350 | 1350000 | 560 | 60 | 320 | 630 | 180 | 1350 | 520 | 2400 | 250 | 120 | 150 | 90 | 5250 |
NJD(DSN)1750 | 1750000 | 620 | 50 | 400 | 710 | 190 | 1500 | 540 | 2600 | 270 | 130 | 160 | 100 | 7100 |
(2) The holdback hole and shaft are mainly connected with flat key, and the dimensions of key and keyway should satisfy the provisions of GB/T1095-1979. The keyway for the holdback hole is fabricated according to the tolerance D10 in GB/T1095-1979 (see Table 16).
(3) The length of shaft extension of the holdback should be equal to the length of inner race of the holdback as far as possible, its min. length should not be less than 5/6 length of inner race so as to ensure the strength of shaft extension and key.
Contact us if you need more details on Backstop. We are ready to answer your questions on packaging, logistics, certification or any other aspects about Bearing、Clutch. If these products fail to match your need, please contact us and we would like to provide relevant information.
Product Categories : Backstop for Belt
Premium Related Products
Other Products
Hot Products
Ep300/3 Drive Belt Rubber Conveyor BeltInterlocking Dog Bone Rubber Flooring, Rubber Paving TilesHot Sale! ! Impact Resistant SBR Rubber Sheet with Fabric InsertionLarge Capacity Chevron Rubber Conveyor Belt Made in ChinaEp/Nn/Cc Conveyor Belt From FactoryFirst Class Anti-Tear Conveyor BeltsEPDM Foaming Strip for Doors & Windows SealingMine, Stone, Sand Cement Fabric Nylon Nn Ep Cc56 Tc70 Steel Cord Black Rubber Conveyor Belt / Belt ConveyorTransmission Belt of Oil-Resistant Conveyor BeltRubber Belt of Impact-Resistant Conveyor Belt for Large Goods TransportaionConveyor Blet / Non-Stick Conveyor BeltPipe Conveyor Belt for Coal MiningWear-Resistant (Transmission) Chervon BeltHeat-Resistant Conveyor Belt for Gas WorksProfessional Sidewall Rubber Conveyor Belt/ Transmission Rubber Conveyor BeltNylon Rubber Conveyor Belt / Transmission Belt Made in China